Royal Sovereign RSL-2702S Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Laminátory Royal Sovereign RSL-2702S. Royal Sovereign RSL-2702S Owner`s manual Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 20
  • Tabulka s obsahem
  • ŘEŠENÍ PROBLÉMŮ
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 0
RSL- 2702S Laminator
OWNER'S MANUAL
Read all instructions carefully before use.
For any Customer Support needs please choose the
Customer Support tab on www.royalsovereign.com
Royal Sovereign International Inc.
www.royalsovereign.com
Zobrazit stránku 0
1 2 3 4 5 6 ... 19 20

Shrnutí obsahu

Strany 1 - OWNER'S MANUAL

RSL- 2702S LaminatorOWNER'S MANUALRead all instructions carefully before use. For any Customer Support needs please choose the Customer Suppo

Strany 2 - TABLE OF CONTENTS

107. CONTROL OF ROLLER PRESSURETo set, pull the pressure lever outward and turn to one of the following positions. OPEN: For detaching and cleanin

Strany 3 - 2. SAFETY PRECAUTIONS

RSL-2702S118. CONTROL PANEL1. UPPER: To change upper roller temperature by pressing button, then up or down arrow. (range 32~302°F or 0~150°C)2.

Strany 4 - 4. PRODUCT IDENTIFICATION

121. Turn on the power switch located on the rear of the machine.2. Set the pressure lever to the "Laminating mode".3. Adjust the roller te

Strany 5 - 5. LOADING FILM

RSL-2702S13— Useful Information — 1. You can preset up to 9 temperature and speed settings in the memory for faster easier use.2. When laminating co

Strany 6 - 6. THREADING FILM

149.2. COLD LAMINATING1. Thread the cold film in accordance with the illustration and instructions 6.2 on page 8.2. Set pressure lever to the proper

Strany 7

RSL-2702S159.3. MOUNTINGFigure 11. Set the laminator to cold by pressing the c/hot button.2. Lay the decaled image face down on a flat surface. Caref

Strany 8 - 6.2. COLD FILM

16Cleaning the Body of the laminatorTo clean the machine body, dampen a cloth with water only and gently wipe the machine clean.Removing Adhesive Buil

Strany 9

RSL-2702S1712. TROUBLESHOOTINGSymptom Cause Possible SolutionMachine will not turn on:a. Power switch is in "0" (Off) positionb. Tripped ci

Strany 10

1813. Recommended Temperature and Speed Settings14. Factory presetFilm thickness Temp RemarkOpp film 32 micron (1.3 mil) 110°C (230°F) 1 - 3Opp film 3

Strany 11

RSL-2702S1915. SPECIFICATIONSDescription RSL-2702SPower supply AC 110V / 60HzPower consumption 1500WMax. laminating width 685mm / 27"wFilm thickn

Strany 12 - 9. LAMINATING STEPS

2TABLE OF CONTENTSTOPIC PAGE1. Introduction ········································································································

Strany 13 - RSL-2702S

20RS International Australia PTY. LTD.30 Prime Drive, Seven Hills, NSW 2147, AustraliaTEL : +61) 2-9674-2127 FAX : +61) 2-9674-2027E-mail : sal

Strany 14 - 9.2. COLD LAMINATING

RSL-2702S3 1. INTRODUCTION2. SAFETY PRECAUTIONSFailure to comply with any of the following safety procedures could result in serious injury. Please

Strany 15

4 3. INCLUDED WITH LAMINATOR4. PRODUCT IDENTIFICATIONPower supply:220V~240VPower supply:100V~120VPART NAME EA REMARK PART NAME EA REMARK FUSE(65T

Strany 16 - 10. USING CROSS CUTTER

RSL-2702S55. LOADING FILM1. As shown in picture 1, insert auto grips onto the upper/lower film shaft.2. As shown in picture 2, using the special too

Strany 17 - 12. TROUBLESHOOTING

66. THREADING FILM1. Turn the power switch on("I" position). Power switch is located in the rear of the unit on the left side.2. Complete

Strany 18 - 14. Factory preset

RSL-2702S78. Carefully pull up the laminate from the lower roll up towards the first idle bar and then around the back side of the second Idler (Cau

Strany 19 - 15. SPECIFICATIONS

81. Follow the steps in the "Loading Film" procedure by loading the upper shaft with pressure sensitive film, e.g. (Royal Print-Pro Film) a

Strany 20 - 16. WARRANTY

RSL-2702S91. Turn the power switch on("I" position). Power switch is located in the rear of the unit on the left side.2. Follow the steps

Komentáře k této Příručce

Žádné komentáře